GLTL 3-in-1 Rotating Cross Hatch Adhesion Tester Cross-Cut Tester Kit with 1mm/2mm/3mm Blades
GLTL 3-in-1 Rotating Cross Hatch Adhesion Tester Cross-Cut Tester Kit with 1mm/2mm/3mm Blades by GLTL at The Synthesizer. MPN: 43237-2. Hurry! Limited time offer. Offer valid only while supplies last. Technical Specification: 1、Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mm.3+0.01mm. 2、Multi-blade cutter addendum straightness: ≯ 0.003mm ≯
Product Description & Reviews
1、Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mm.3+0.01mm.
2、Multi-blade cutter addendum straightness: ≯ 0.003mm ≯ 0.006mm.
3、Multi-blade cutter tooth tip width: ≯ 0.05mm.
4 、Cutter spacing and cutter types: 1mm and 2mm with 11 teeth ，3mm with 6 teeth
1.Placing the test piece on a tablet of sufficient hardness.
2.Holding the handle of the program grid, keeping the multi-blade cutter perpendicular to the plane of the test piece.
3.By using the uniform force, with the manner of not fibrillation and balance and 20-50mm/S cutting speed to draw.
4.Rotating the test piece to 90 °, repeating the above operations, so as to enable to cut a grid lattice graphics.
5.Brushing the two diagonals of grid lattice graphics by using the soft brush gently backward and forward each five times.
6.The test should be taken at least in three different locations on the test piece. If the results of three positions are
different,the test should be repeated in more than three positions, and record all results.
7.If it need to replace the multi-blade cutter, use the screwdriver to unscrew the two screws on the cutter body and change the
cutter, affix the edge of cutter to the handle, then tighten the screws.
1. All the incision should penetrate the coating, cut into the substrate but must not be too deep.
2. If the coating is too thick and hard to penetrate in the substrate, then the test is invalid.However,
it should be explained in the test report.
3. In some special situation or special requirements, it must be compatible with the tape method for the final determination.
Features & Highlights
- 1， The instrument is designed and manufactured according to the standard of ISO2409-1992；
- 2， Used in GB/T9286-98, BS 3900 E6/ASTM D3359 ；
- 3， Standard tool 3-in-1 Rotating Cross Hatch Adhesion Tester Cross-Cut Tester Kit with 1mm/2mm/3mm blades；
- Maybe you need to use Pencil Hardness Tester：https://www.amazon.com/dp/B077G2D37Z
Maybe you need to use Matching blade：https://www.amazon.com/dp/B072JK6CDD
7.2 x 1.89 x 9.53 inches
Have questions about this item, or would like to inquire about a custom or bulk order?
If you have any questions about this product by GLTL, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.
Related Best Sellers
This method is used for determining the parallel groove paint adhesion of one or many layers on a substrate, generally a metal panel. Cross-Cut Tester Kits are available in 2 different crosscut blade versions, one is a multi-cut blade with 6 cutting ...
By American Tool Exchange
mpn: 66406, ean: 0024721664068,
96 PK YELLOW LUMBER CRAYONWorks in oily, slick, wet, cold, or dry conditions. Marks on virtually any surface, including lumber, concrete, ceramics, and metal. Long lasting, waterproof and non-toxic. 4-1/2" overall. Yellow color.... ...
mpn: FBA_9401849, ean: 0796299401849,
30X magnification. 5-sec angular accuracy. Tilt sensor, +/-3-Feet. ...
By Custom Building Products
mpn: 83-TS26, ean: 0092975830263,
The Box Screed Set features accurate straight edge for bathtubs, shower stalls and floors, Lightweight 3/4" x 4" extruded box aluminum with reinforced center rib, Wrap-around handle (included with set)....